in /etc/modules.conf I have the line:
options adm1021 ignore=0,0x4e
My sensors.conf looks like:
chip "adm1021-*"
# These are as advised in the data sheet
label in0 "+2.5V"
label in1 "VCCP"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "VCC"
label temp1 "SYS Temp"
label temp2 "CPU Temp"
chip "adm1024-*"
#
# These settings work for me, adjust for your system
#
label fan1 "CPU1 fan"
label fan2 "CPU2 fan"
label temp "SYS Temp"
label temp1 "CPU2 Temp"
label temp2 "CPU1 Temp"
ignore "2.5V" # This register is also used for temp2
ignore "Vccp1"
chip "lm84-*"
# These are as advised in the data sheet
label in0 "+2.5V"
label in1 "VCCP"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "VCC"
label temp1 "SYS Temp"
label temp2 "CPU Temp"
--
/* Greg Evans, Bloomington, MN., USA - gje at parrotheaven.com */
-------------
"Freedom is more important than happiness" - Tom Robbins
Austad, Jay [austad at marketwatch.com] wrote:
> Also, do you pass any options when loading the module?
>
> > -----Original Message-----
> > From: Greg Evans [mailto:gje at parrotheaven.com]
> > Sent: Thursday, November 15, 2001 9:47 PM
> > To: tclug-list at mn-linux.org
> > Subject: Re: [TCLUG] lm_sensors
> >
> >
> > It's a Soyo Dragon+. If I remember correctly I
> > downloaded the cvs version
> > of lm_sensors2. Compiled the basic i2c stuff with the
> > kernel, then compiled and
> > installed the cvs lm_sensors and did a depmod -a. modprobe
> > i2c-core, modprobe
> > adm1021, and then spent (and still spend) way to much time
> > trying to figure out
> > what to put in /etc/sensors.conf to actually get it to tell
> > me something useful.
> > So far running sensors still only tells me my cpu temp.
> >
> > --
> > /* Greg Evans, Bloomington, MN., USA - gje at parrotheaven.com */
> > -------------
> > "Nothing is more terrible than ignorance in action."
> > -- Johann Wolfgang von Goethe
> >
> > Austad, Jay [austad at marketwatch.com] wrote:
> > > > Using the adm1021 driver I was able to get the cpu
> > > > temperture, but I still
> > > > can't figure out how to read the chipset temp, or the fan
> > monitors.
> > >
> > > Was this on a Soyo Dragon or Dragon+? What did you do to
> > get it working?
> > >
> > > Jay
> > > _______________________________________________
> > > Twin Cities Linux Users Group Mailing List -
> > Minneapolis/St. Paul, Minnesota
> > > http://www.mn-linux.org
> > > tclug-list at mn-linux.org
> > > https://mailman.mn-linux.org/mailman/listinfo/tclug-list
> > _______________________________________________
> > Twin Cities Linux Users Group Mailing List - Minneapolis/St.
> > Paul, Minnesota
> > http://www.mn-linux.org
> > tclug-list at mn-linux.org
> > https://mailman.mn-linux.org/mailman/listinfo/tclug-list
> >
> _______________________________________________
> Twin Cities Linux Users Group Mailing List - Minneapolis/St. Paul, Minnesota
> http://www.mn-linux.org
> tclug-list at mn-linux.org
> https://mailman.mn-linux.org/mailman/listinfo/tclug-list