Where can one obtain that hex decoder? Jason On Mon, 1 Dec 1997, Kevin Smith wrote: > At 02:51 PM 11/28/97 -0500, Chris A. Epler wrote: > >I noticed something new (?) in the modemdiag output of 5.0Ap36, towards the > >end there is a sequence of > > > >BEGIN<misc hex string>END > > <snip> > > >BEGINaa14ab14ac14ba0bb0bc0ca77cb67cc118da255ea255eb255fa110ga10gb255ha1hb0h > c3hd0he0hf0hg0hh0hi0ia255ib255ic0ja0jb0jc0jd0ka1kb1kc0kd0ke0kf0kg0kh255ki255 > kj255kk0kl82la0lb0ma0mb42mc55na0nb0oa255ob255oc255pa12END > > The hex string bt. the BEGIN and END is the output of AT&V2 command. > It gives you additional information such as Signal to Noise ratio, > retrain requested by server, retrain requested by client, whether > client is a USR modem, etc. Rockwell has a program to parse these > results. It's free. > Here is an example of the parsed output: > > Current Transmit Speed : 31200 bps > Minimum Transmit Speed : 31200 bps > Maximum Transmit Speed : 31200 bps > Current Receive Speed : 28800 bps > Minimum Receive Speed : 28800 bps > Maximum Receive Speed : 28800 bps > Error Correction Protocol : LAP-M > Compression type : V.42bis > Modulation : V.34 > Symbol Rate : 3429 baud > Transmit Carrier Frequency : 1959 Hz > Receive Carrier Frequency : 1959 Hz > Last AGC Gain value : -12.000000 dB > Minimum AGC Gain value : -12.000000 dB > Maximum AGC Gain value : -12.000000 dB > Transmit level : 10 > Transmit level reduction : 3 > Last EQM read : 13 > Minimum EQM value : FF > Maximum EQM value : 00 > # of EQM hits : 0 > EQM Sum value : 0034A8 > Reserved : 0 > Reserved : 0 > SNR Ratio : 37.200000 dB > Minimum SNR Ratio : 37.200000 dB > Maximum SNR Ratio : 37.200000 dB > # of Local Retrains : 0 > # of Remote Retrains : 0 > # of Local Rate Renegs : 0 > # of Remote Rate Renegs : 0 > Transmit Non-linear Encoding: YES > Receive Non-linear Encoding : YES > Transmit precoding : NO > Receive precoding : YES > Transmit Shaping : No > Receive Shaping : Yes > Trellis mapping : 64 state > Pre-emphasis : Filter #0 > Upper band edge : 3825.000000 > Lower band edge : 150.000000 > Round trip delay : 3.207495 ms > Info Sequence 0 : 21FF > Highest Transmit State : 67 > Highest Receive State : 67 > Time connected : 0 Hours 0 Minutes 19 Seconds > Auto gain amplitude : 0 dB > Auto gain attenuation : 0 dB > Maximum retransmissions : 1 > Total retransmissions : 0 > Disconnect Reason : Link Disconnect > New Field in Q : 255 > > > > > Kevin > > > ++ Ascend Users Mailing List ++ > To unsubscribe: send unsubscribe to ascend-users-request@bungi.com > To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>> > ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>> </PRE> <!--X-MsgBody-End--> <!--X-Follow-Ups--> <HR> <STRONG>Follow-Ups</STRONG>: <UL> <LI><STRONG><A HREF="msg11311.html">Re: (ASCEND) modemdiag output on 5.0Ap36</A></STRONG></LI> <UL> <LI><EM>From</EM>: Kevin Smith <kevin@ascend.com></LI> </UL> <LI><STRONG><A HREF="msg11294.html">Re: (ASCEND) modemdiag output on 5.0Ap36</A></STRONG></LI> <UL> <LI><EM>From</EM>: "Chris A. Epler" <cepler@esinet.net></LI> </UL> </UL> <!--X-Follow-Ups-End--> <!--X-References--> <STRONG>References</STRONG>: <UL> <LI><STRONG><A HREF="msg11260.html">Re: (ASCEND) modemdiag output on 5.0Ap36</A></STRONG></LI> <UL> <LI><EM>From</EM>: Kevin Smith <kevin@ascend.com></LI> </UL> </UL> <!--X-References-End--> <!--X-BotPNI--> <HR> <UL> <LI>Prev by Date: <STRONG><A HREF="msg11277.html">Re: (ASCEND) Max 5.0Ap36</A></STRONG> </LI> <LI>Next by Date: <STRONG><A HREF="msg11274.html">Re: (ASCEND) anyone know if bri bug is fixed yet?</A></STRONG> </LI> <LI>Prev by thread: <STRONG><A HREF="msg11331.html">Re: (ASCEND) modemdiag output on 5.0Ap36</A></STRONG> </LI> <LI>Next by thread: <STRONG><A HREF="msg11294.html">Re: (ASCEND) modemdiag output on 5.0Ap36</A></STRONG> </LI> <LI>Index(es): <UL> <LI><A HREF="mail3.html#11278"><STRONG>Main</STRONG></A></LI> <LI><A HREF="thrd259.html#11278"><STRONG>Thread</STRONG></A></LI> </UL> </LI> </UL> <!--X-BotPNI-End--> <!--X-User-Footer--> <!--X-User-Footer-End--> </BODY> </HTML>