> At 08:02 PM 02/04/97 +0200, Zivojnovic Ranko wrote: > >Hi! > > > >I have heavily modified version of Livingston 1.16 RADIUS in order > >to have it serve our needs. Anyway, as much as I have noticed > >difference between Livingston PM's accounting and Ascend accounting > >is that PM will send an "Acct" packet only if the session (PPP for example) > >has been successfully established. In difference to that the Ascend will send > >it immediately after it authenticates. For that reason in the "Acct" > packets of the > >Ascends there is no information about the IP address used for the > connectivity. > > > >I need that info (IP number) on my RADIUS server and my question is: > >Is there a way of retrieving such information from Ascend client through > RADIUS or > >setting up Ascend to send "Acct" packets only after successful establishment > >of whatever "User-Service-Type" attribute specifies? > > You could set the: > Auth Pool: to "YES" > > This option is used to pre-assign an IP address before > ppp/ipcp > negotiates an IP address. This allows radius to write the > IP address > into the accounting "start" record. > > Ethernet -> > Ethernet Mod Config -> > Auth -> > Auth Pool = YES > Finally got around to testing this. It does not work. I set the Auth Pool item to "yes" and rebooted each of my maxen (ouch). My maxen are running 5.0Ap3 Here is a typical entry from a text based terminal authentication: Thu Jun 26 08:34:42 1997 User-Name = "Pugor" NAS-IP-Address = "204.157.220.24" NAS-Port = 20211 Acct-Status-Type = Start Acct-Delay-Time = 0 Acct-Session-Id = "266782199" Acct-Authentic = RADIUS User-Id = "Pugor" NAS-Identifier = "max2.aa.net" Note the lack of Framed-Protocol and Framed-IP-Address entries, but the server did indeed start PPP session. Here is a user that authenticated using PAP: Thu Jun 26 08:34:53 1997 User-Name = "lberg" NAS-IP-Address = "204.157.220.24" NAS-Port = 20208 Acct-Status-Type = Start Acct-Delay-Time = 0 Acct-Session-Id = "266782201" Acct-Authentic = RADIUS Framed-Protocol = PPP Framed-IP-Address = "205.199.142.33" User-Id = "lberg" NAS-Identifier = "max2.aa.net" I would really, really like to have the IP address assigned in the accounting start packet. What can be done? ----------------------------------------------------------------------------- Joe Portman - Alternate Access Inc. Affordable, Reliable Internet ----------------------------------------------------------------------------- ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com To get FAQ'd: <<A HREF="http://www.shore.net/~dreaming/ascend-faq">http://www.shore.net/~dreaming/ascend-faq</A>> or <<A HREF="ftp://ftp.shore.net/members/dreaming/ascend-faq.txt">ftp://ftp.shore.net/members/dreaming/ascend-faq.txt</A>> </PRE> <!--X-MsgBody-End--> <!--X-Follow-Ups--> <HR> <STRONG>Follow-Ups</STRONG>: <UL> <LI><STRONG><A HREF="msg06068.html">Re: (ASCEND) RADIUS Accounting</A></STRONG></LI> <UL> <LI><EM>From</EM>: Dave Mitton <dmitton@baynetworks.com></LI> </UL> </UL> <!--X-Follow-Ups-End--> <!--X-References--> <!--X-References-End--> <!--X-BotPNI--> <HR> <UL> <LI>Prev by Date: <STRONG><A HREF="msg05891.html">(ASCEND) Bridge Addresses</A></STRONG> </LI> <LI>Next by Date: <STRONG><A HREF="msg05889.html">Re: (ASCEND) 56k Low Port solution?</A></STRONG> </LI> <LI>Prev by thread: <STRONG><A HREF="msg05887.html">(ASCEND) Max 400x, Pipe75, DHCP</A></STRONG> </LI> <LI>Next by thread: <STRONG><A HREF="msg06068.html">Re: (ASCEND) RADIUS Accounting</A></STRONG> </LI> <LI>Index(es): <UL> <LI><A HREF="mail120.html#05890"><STRONG>Main</STRONG></A></LI> <LI><A HREF="thrd57.html#05890"><STRONG>Thread</STRONG></A></LI> </UL> </LI> </UL> <!--X-BotPNI-End--> <!--X-User-Footer--> <!--X-User-Footer-End--> </BODY> </HTML>