(ASCEND) LCP hangup.

To: "ahobbs@unitel.com.au" <ahobbs@unitel.com.au>, Dean Frye <dfrye@ascend.com.au>, "Lou_Aloi@ascend.com" <Lou_Aloi@ascend.com>, "ascend-users@bungi.com" <ascend-users@bungi.com>, staff@1earth.net, "inet-access@earth.com" <inet-access@earth.com>
Subject: (ASCEND) LCP hangup.
From: Phillip Grasso <phillip@1earth.net>
Date: Thu, 09 Apr 1998 19:48:08 +1000
Sender: owner-ascend-users@max.bungi.com
G'day all,
    I've had this problem for the last month,
max 1800, software 6.0.2, 2 microlinks (4 * 64K = 256K) connecting to
Cisco 5200, PRA Macrolink (No ESTI) or PRI, IOS 11.2(5.4P)
When the load on the cisco goes to the roof, it start to get packet
loss, then no traffic,
afterwards a disconnection.
This seems to only happen to our connection out of 20 or so other MP
connections to the 5200.
Anyone help with this?

Here are the Logs of Both ascend & cisco

CISCO 5200!
wol2.Wollongong#
PPP Serial0:19: exceeded max retries taking LCP down.
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:19, changed
state
to down
PPP Serial0:20: exceeded max retries taking LCP down.
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:20, changed
state
to down
PPP Serial0:21: exceeded max retries taking LCP down.
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:21, changed
state
to down
PPP Serial0:22: exceeded max retries taking LCP down.
Serial0:15: remove route to 139.130.44.4
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:22, changed
state
to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access12,
changed
state to down
%ISDN-6-DISCONNECT: Interface Serial0:19  disconnected from <unknown
phone number> 1earth, call lasted 1116 seconds
%ISDN-6-DISCONNECT: Interface Serial0:20  disconnected from <unknown
phone number> 1earth, call lasted 1087 seconds
%ISDN-6-DISCONNECT: Interface Serial0:21  disconnected from <unknown
phone number> 1earth, call lasted 1087 seconds
%ISDN-6-DISCONNECT: Interface Serial0:22  disconnected from <unknown
phone number> 1earth, call lasted 1085 seconds
ISDN Se0:15: TX ->  DISCONNECT pd = 8  callref = 0x80C4
        Cause i = 0x8090 - Normal call clearing
ISDN Se0:15: TX ->  DISCONNECT pd = 8  callref = 0x80A3
        Cause i = 0x8090 - Normal call clearing
ISDN Se0:15: TX ->  DISCONNECT pd = 8  callref = 0x8015
        Cause i = 0x8090 - Normal call clearing
ISDN Se0:15: TX ->  DISCONNECT pd = 8  callref = 0x804B
        Cause i = 0x8090 - Normal call clearing
Serial0:20: Protocol = 0x3D dropped.
%LINK-3-UPDOWN: Interface Virtual-Access12, changed state to down
ISDN Se0:15: RX <-  RELEASE pd = 8  callref = 0x00C4
ISDN Se0:15: RX <-  RELEASE pd = 8  callref = 0x0015
ISDN Se0:15: RX <-  RELEASE pd = 8  callref = 0x00A3
ISDN Se0:15: RX <-  RELEASE pd = 8  callref = 0x004B
ISDN Se0:15: TX ->  RELEASE_COMP pd = 8  callref = 0x80C4
%LINK-3-UPDOWN: Interface Serial0:19, changed state to down
ISDN Se0:15: TX ->  RELEASE_COMP pd = 8  callref = 0x8015
%LINK-3-UPDOWN: Interface Serial0:21, changed state to down
ISDN Se0:15: TX ->  RELEASE_COMP pd = 8  callref = 0x80A3
%LINK-3-UPDOWN: Interface Serial0:20, changed state to down
%LINK-3-UPDOWN: Interface Serial0:22, changed state to down
ISDN Se0:15: TX ->  RELEASE_COMP pd = 8  callref = 0x804B
Serial0:19: dropped, LCP not open.  Protocol = 0x3D
ISDN Se0:15: RX <-  SETUP pd = 8  callref = 0x0092
        Bearer Capability i = 0x8890
        Channel ID i = 0xA18317
        Called Party Number i = 0xC1, '42211200'
ISDN Se0:15: Incoming call id = 0x3E9B
%LINK-3-UPDOWN: Interface Serial0:23, changed state to up
ISDN Se0:15: TX ->  CALL_PROC pd = 8  callref = 0x8092
        Channel ID i = 0xA98317
ISDN Se0:15: TX ->  CONNECT pd = 8  callref = 0x8092
        Channel ID i = 0xA98317
ISDN Se0:15: RX <-  CONNECT_ACK pd = 8  callref = 0x0092
ppp: sending CONFREQ, type = 3 (CI_AUTHTYPE), value = 0xC223/5
ppp: sending CONFREQ, type = 5 (CI_MAGICNUMBER), value = 0x904DDBC
ppp: sending CONFREQ, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: sending CONFREQ, type = 19 (CI_ENDPOINT_DISC)
PPP Serial0:23: received config for type = 1 (MRU) value = 1524 acked
PPP Serial0:23: received config for type = 17 (MULTILINK_MRRU) value =
1524 acked
PPP Serial0:23: received config for type = 19 (ENDPOINT_DISC) value =
00c0.7b6d.1a3b acked
PPP Serial0:23: state = ACKsent fsm_rconfack(0xC021): rcvd id 75
ppp: config ACK received, type = 3 (CI_AUTHTYPE), value = 0xC223
ppp: config ACK received, type = 5 (CI_MAGICNUMBER), value = 0x904DDBC
ppp: config ACK received, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: config ACK received, type = 19 (CI_ENDPOINT_DISC)
Serial0:23: Protocol = 0x3D dropped.
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:23, changed
state
to up
Serial0:23: Protocol = 0x3D dropped.
%ISDN-6-CONNECT: Interface Serial0:23 is now connected to <unknown phone

number> 1earth
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
Serial0:23: Protocol = 0x3D dropped.
%LINK-3-UPDOWN: Interface Virtual-Access7, changed state to up
ipcp: sending CONFREQ, type = 3 (CI_ADDRESS), Address = 139.130.44.1
PPP Virtual-Access7: state = REQsent fsm_rconfack(0x8021): rcvd id 1
ipcp: config ACK received, type = 3 (CI_ADDRESS), Address = 139.130.44.1

%LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access7, changed

state to up
ipcp: sending CONFREQ, type = 3 (CI_ADDRESS), Address = 139.130.44.1
ppp Virtual-Access7: Negotiate IP address: her address 139.130.44.4
(ACK)
ppp: ipcp_reqci: returning CONFACK.
PPP Virtual-Access7: state = ACKsent fsm_rconfack(0x8021): rcvd id 2
ipcp: config ACK received, type = 3 (CI_ADDRESS), Address = 139.130.44.1

ISDN Se0:15: RX <-  SETUP pd = 8  callref = 0x002C
        Bearer Capability i = 0x8890
        Channel ID i = 0xA1831E
        Called Party Number i = 0xC1, '42211200'
ISDN Se0:15: Incoming call id = 0x3E9C
%LINK-3-UPDOWN: Interface Serial0:30, changed state to up
ISDN Se0:15: TX ->  CALL_PROC pd = 8  callref = 0x802C
        Channel ID i = 0xA9831E
ISDN Se0:15: TX ->  CONNECT pd = 8  callref = 0x802C
        Channel ID i = 0xA9831E
ISDN Se0:15: RX <-  SETUP pd = 8  callref = 0x003A
        Bearer Capability i = 0x8890
        Channel ID i = 0xA1830B
        Called Party Number i = 0xC1, '42211200'
ISDN Se0:15: Incoming call id = 0x3E9D
%LINK-3-UPDOWN: Interface Serial0:10, changed state to up
ISDN Se0:15: TX ->  CALL_PROC pd = 8  callref = 0x803A
        Channel ID i = 0xA9830B
ISDN Se0:15: TX ->  CONNECT pd = 8  callref = 0x803A
        Channel ID i = 0xA9830B
ISDN Se0:15: RX <-  CONNECT_ACK pd = 8  callref = 0x002C
Serial0:15: install route to 139.130.44.4
ISDN Se0:15: RX <-  CONNECT_ACK pd = 8  callref = 0x003A
ppp: sending CONFREQ, type = 3 (CI_AUTHTYPE), value = 0xC223/5
ppp: sending CONFREQ, type = 5 (CI_MAGICNUMBER), value = 0x9056C09
ppp: sending CONFREQ, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: sending CONFREQ, type = 19 (CI_ENDPOINT_DISC)
PPP Serial0:30: received config for type = 1 (MRU) value = 1524 acked
PPP Serial0:30: received config for type = 17 (MULTILINK_MRRU) value =
1524 acked
PPP Serial0:30: received config for type = 19 (ENDPOINT_DISC) value =
00c0.7b6d.1a3b acked
ppp: sending CONFREQ, type = 3 (CI_AUTHTYPE), value = 0xC223/5
ppp: sending CONFREQ, type = 5 (CI_MAGICNUMBER), value = 0x9056C26
ppp: sending CONFREQ, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: sending CONFREQ, type = 19 (CI_ENDPOINT_DISC)
PPP Serial0:10: received config for type = 1 (MRU) value = 1524 acked
PPP Serial0:10: received config for type = 17 (MULTILINK_MRRU) value =
1524 acked
PPP Serial0:10: received config for type = 19 (ENDPOINT_DISC) value =
00c0.7b6d.1a3b acked
PPP Serial0:30: state = ACKsent fsm_rconfack(0xC021): rcvd id 157
ppp: config ACK received, type = 3 (CI_AUTHTYPE), value = 0xC223
ppp: config ACK received, type = 5 (CI_MAGICNUMBER), value = 0x9056C09
ppp: config ACK received, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: config ACK received, type = 19 (CI_ENDPOINT_DISC)
ISDN Se0:15: RX <-  SETUP pd = 8  callref = 0x0083
        Bearer Capability i = 0x8890
        Channel ID i = 0xA1830C
        Called Party Number i = 0xC1, '42211200'
ISDN Se0:15: Incoming call id = 0x3E9E
%LINK-3-UPDOWN: Interface Serial0:11, changed state to up
ISDN Se0:15: TX ->  CALL_PROC pd = 8  callref = 0x8083
        Channel ID i = 0xA9830C
ISDN Se0:15: TX ->  CONNECT pd = 8  callref = 0x8083
        Channel ID i = 0xA9830C
PPP Serial0:10: state = ACKsent fsm_rconfack(0xC021): rcvd id 214
ppp: config ACK received, type = 3 (CI_AUTHTYPE), value = 0xC223
ppp: config ACK received, type = 5 (CI_MAGICNUMBER), value = 0x9056C26
ppp: config ACK received, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: config ACK received, type = 19 (CI_ENDPOINT_DISC)
ISDN Se0:15: RX <-  CONNECT_ACK pd = 8  callref = 0x0083
ppp: sending CONFREQ, type = 3 (CI_AUTHTYPE), value = 0xC223/5
ppp: sending CONFREQ, type = 5 (CI_MAGICNUMBER), value = 0x90575DE
ppp: sending CONFREQ, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: sending CONFREQ, type = 19 (CI_ENDPOINT_DISC)
PPP Serial0:11: received config for type = 1 (MRU) value = 1524 acked
PPP Serial0:11: received config for type = 17 (MULTILINK_MRRU) value =
1524 acked
PPP Serial0:11: received config for type = 19 (ENDPOINT_DISC) value =
00c0.7b6d.1a3b acked
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:10, changed
state
to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:30, changed
state
to up
PPP Serial0:11: state = ACKsent fsm_rconfack(0xC021): rcvd id 192
ppp: config ACK received, type = 3 (CI_AUTHTYPE), value = 0xC223
ppp: config ACK received, type = 5 (CI_MAGICNUMBER), value = 0x90575DE
ppp: config ACK received, type = 17 (CI_MULTILINK_MRRU), value = 0x5F4
ppp: config ACK received, type = 19 (CI_ENDPOINT_DISC)
%ISDN-6-CONNECT: Interface Serial0:11 is now connected to
00c0.7b6d.1a3b
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0:11, changed
state
to up
wol2.Wollongong#

Ascend 1800,
 > PPPIF-92: _pppClose called
PPPIF-92: cleanup pass
PPPIF-94: _pppClose called
PPPIF-94: cleanup pass
PPPIF-93: _pppClose called
PPPIF-93: cleanup pass
PPPIF-95: _pppClose called
PPPIF-109: pppMpNegUntimeout last 1 layer 0
PPPIF-95: cleanup pass
PPPIF: open: routeid 453, incoming NO
PPPIF-96: _initAuthentication
PPPIF-96: auth mode 2
PPPIF-96: CHAP auth, outgoing
PPPIF-96: Link Is up.
PPPIF-96: pppMpNegUntimeout last 0 layer 0
PPPIF-96: pppMpNegUntimeout last 0 layer 0
PPPIF-96: LCP Opened, local 'telstra 256k', remote ''
PPPIF-96: _openAuthentication
PPPIF-96: pppMpNegUntimeout last 0 layer 1
PPPIF-96: Auth Opened
PPPIF-96: Remote hostName is 'telstra 256k'
PPPIF-96: prep MP bundle for telstra 256k
PPPIF-96: new MP bundle
PPPIF-96: First channel, MpID 110
PPPIF: Assigning vjInfo (B057F1A0) and bncpInfo(B05381F0)
PPPIF-96: CBCP Opened
PPPIF-96: opening CCP
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: opening IPNCP: 139.130.44.4 -> 139.130.44.1
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 6
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: pppMpNegTimeout layer 4
PPPIF-96: pppMpSendNeg Pkt
PPPIF-96: CCP closed
PPPIF-96: pppMpNegUntimeout last 0 layer 4
PPPIF-96: pppMpNegUntimeout last 0 layer 4
PPPIF-96: IPNCP Opened to 139.130.44.1
PPPIF: open: routeid 1, incoming NO
PPPIF-98: _initAuthentication
PPPIF-98: auth mode 2
PPPIF-98: CHAP auth, outgoing
PPPIF-98: Link Is up.
PPPIF: open: routeid 454, incoming NO
PPPIF-97: _initAuthentication
PPPIF-97: auth mode 2
PPPIF-97: CHAP auth, outgoing
PPPIF-97: Link Is up.
PPPIF-98: pppMpNegUntimeout last 0 layer 0
PPPIF-98: pppMpNegUntimeout last 0 layer 0
PPPIF-98: LCP Opened, local 'telstra 256k', remote ''
PPPIF-98: _openAuthentication
PPPIF-97: pppMpNegUntimeout last 0 layer 0
PPPIF-97: pppMpNegUntimeout last 0 layer 0
PPPIF-97: LCP Opened, local 'telstra 256k', remote ''
PPPIF-97: _openAuthentication
PPPIF-98: pppMpNegUntimeout last 0 layer 1
PPPIF-98: Auth Opened
PPPIF-98: Remote hostName is 'telstra 256k'
PPPIF-98: prep MP bundle for telstra 256k
PPPIF-98: subseq chan, MpID 110
PPPIF: Pre-assigned vjInfo (B057F1A0) and bncpInfo (B05381F0)
PPPIF-97: pppMpNegUntimeout last 0 layer 1
PPPIF-97: Auth Opened
PPPIF-97: Remote hostName is 'telstra 256k'
PPPIF-97: prep MP bundle for telstra 256k
PPPIF-97: subseq chan, MpID 110
PPPIF: Pre-assigned vjInfo (B057F1A0) and bncpInfo (B05381F0)
PPPIF: open: routeid 2, incoming NO
PPPIF-99: _initAuthentication
PPPIF-99: auth mode 2
PPPIF-99: CHAP auth, outgoing
PPPIF-99: Link Is up.
PPPIF-99: pppMpNegUntimeout last 0 layer 0
PPPIF-99: pppMpNegUntimeout last 0 layer 0
PPPIF-99: LCP Opened, local 'telstra 256k', remote ''
PPPIF-99: _openAuthentication
PPPIF-99: pppMpNegUntimeout last 0 layer 1
PPPIF-99: Auth Opened
PPPIF-99: Remote hostName is 'telstra 256k'
PPPIF-99: prep MP bundle for telstra 256k
PPPIF-99: subseq chan, MpID 110
PPPIF: Pre-assigned vjInfo (B057F1A0) and bncpInfo (B05381F0)



++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>
Prev by Date: Re: (ASCEND) Unusual radius accounting codes
Next by Date: Re: (ASCEND) Backoff Q full error
Prev by thread: No Subject
Next by thread: (ASCEND) P75 NAT
Index(es):
- Date
- Thread