Re: (ASCEND) Is this the cause of a 7.0.4 upgrade?

["Dale R. Henninger" <daleh@pconline.com>]

Yes, it is close to being full.  In fact, the cause 9 below means "no
modems available" 

Is there a way to keep the channel open until the modem resets and then
tell the switch that channel is ready to go for another call?


Dale



On Sat, 8 May 1999, Bob K wrote:

> Hmm.  Perhaps a clue is that it takes 6 seconds to reset a modem?  Does it
> happen only when it's almost full?
> 
> On Sat, 8 May 1999, Dale R. Henninger wrote:
> 
> > More info:
> > 
> > It appears it happens only when a call comes in several seconds after a
> > call has just cleared on the same line/channel:
> > 
> > May  8 20:27:08 m18-2 ASCEND: slot 2 port 1, line 5, channel 1, Call
> > Disconnected [MBID 209; ->6039240] 
> > May  8 20:27:08 m18-2 ASCEND: slot 2 port 1, Call Terminated [MBID 209;
> > ->6039240] 
> > May  8 20:27:12 m18-2 ASCEND: slot 0 port 0, line 5, channel 1, Incoming
> > Call, MBID 222 [MBID 222; ->6039240] 
> > May  8 20:27:12 m18-2 ASCEND: slot 0 port 0, Call Refused [MBID 222;
> > ->6039240] 
> > May  8 20:27:13 m18-2 ASCEND: call 91 CL 0K   c=9 p=2
> > May  8 20:27:13 m18-2 ASCEND: slot 0 port 0, line 5, channel 1, Far End
> > Hung Up
> > 
> > 
> > Notice 4 seconds before the call Refused, line 5 channel 1 disconnected. 
> > 
> > 
> > Dale
> > 
> > 
> > 
> > On Sat, 8 May 1999, Adam Neat wrote:
> > 
> > > Hello,
> > > 
> > > We did an upgrade on a few of our max units (3 4K's and 1 1800). 
> > > 
> > > On the 1800, we have a client who is dialing in to us over ISDN with 128K. They are calling with a Cisco 1003 router.
> > > 
> > > Up until we did the upgrades, there was no proble. Now, the client is dialing in, and the message we are getting on the max menu log is 
> > > 
> > > "call refused" and then "far end hung up".
> > > 
> > > The syslog output suggests that tehy are dialing in with their username being their isdn phone number!
> > > 
> > > The client hasnt changed anything and they understand the workings of routers, etc.
> > > 
> > > We havent changed a thing.
> > > 
> > > Has anyone else seen this issue with 7.0.4 for a Max1800 or possibly even a 4000?
> > > 
> > > regards
> > > 
> > > adam
> > > 
> > > 
> > > ------------------------------------------------
> > >                   IPAX Systems
> > >               Melbourne, Australia
> > >             National Systems Manager
> > >             Ops Tel:   1800 894 894
> > >             Ops Fax:  03 - 9801-8533
> > >         Web Site http://www.ipax.com.au
> > > ------------------------------------------------
> > > 
> > > 
> > > ++ Ascend Users Mailing List ++
> > > To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> > > To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> > > 
> > 
> > 
> > -------------------------------------------------
> > Dale Henninger                   817 Vandalia St.
> > pcOnline Internet Services     St. Paul, MN 55114
> > 651/647-6774 Voice               651/647-5956 Fax 
> > daleh@pconline.com        http://www.pconline.com
> > 
> > ++ Ascend Users Mailing List ++
> > To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> > To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> > 
> 
> melange@yip.org - Napalm: Cures what ails ya
> 
> ++ Ascend Users Mailing List ++
> To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> 


-------------------------------------------------
Dale Henninger                   817 Vandalia St.
pcOnline Internet Services     St. Paul, MN 55114
651/647-6774 Voice               651/647-5956 Fax 
daleh@pconline.com        http://www.pconline.com

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>