Re: (ASCEND) MAX TNT with R2MFC

[KY Lee <kylee@tm.net.my>]

Hi , 

Try to turn off your caller-id ..
go to the E1 profile and set caller-id = no 

I suspect the problem you have is because the TNT  is expecting your switch
to send the CLID but in fact the switch is not sending the number , so the
TNT will polls the number until timeout... 

Besides that, if you are using modem, try to set your default-call-type as
the voice and also you have the call-route profile .. 

In your configuration, your TNT is expecting 4 digits from the switch and
make sure you have the right number in you call-route profile as well.. 




At 13:11 03-05-99 -0500, Rafael Espinosa wrote:
>Hi ,I have problem . i force the MAX-TNT to answer the incoming calls 
>coming from Meridian .
>The problem is that we can use only the R2 MFC signaling in E1 trunk
>between MAX and Meridian, Now the MAX can see the trunk . It shows the 
>good
>state of E1 line all up and  in status window, 's' mark for signaling
>(16th) time slot and 'LA' status). But any call from the external
>phone/modem cannot be done into the MAX.
>
>And is to send the 'B' signal which gives the switch the 'Subscriber
>is available' state, and therefore the switch can initiate the 'open
>line' state. BUT MAX DOESN'T RESPOND ANYTHING after the receiving the
>first digit of the called number! Then returns the ' busy'
>tone to the handset. and i see "r" by not *
>I've tried the different setups for  MAX in E1 line profile Nothing could 
>I change :-((
>
>Please help me, if you can!
>the release is 7.0.1 in MAXTNT
>the configuration is 
>
>
>enabled = yes
>t-online-type = none
>frame-type = 2ds
>clock-source = eligible
>clock-priority = middle-priority
>signaling-mode = e1-r2-signaling
>default-call-type = digital
>switch-type = switch-cas
>incoming-call-handling = internal-processing
>front-end-type = short-haul
>overlap-receiving = no
>pri-prefix-number = ""
>trailing-digits = 2
>t302-timer = 10000
>channel-config = [ { unused-channel 9 "" { any-shelf any-slot 0 } 1 } { 
>switche+
>layer3-end = x-side
>layer2-end = b-side
>nl-value = 64
>loop-avoidance = 7
>number-complete = 4-digits
>group-b-answer-signal = signal-b-1
>group-b-busy-signal = signal-b-3
>group-b-no_match-signal = signal-b-7
>group-ii-signal = signal-ii-2
>input-sample-count = one-sample
>answer-delay = 200
>caller-id = get-caller-id
>hunt-grp-phone-number-1 = ""
>hunt-grp-phone-number-2 = ""
>hunt-grp-phone-number-3 = ""
>collect-incoming-digits = no
>r1-use-anir = no
>r1-first-digit-timer = 340
>r1-anir-delay = 350
>r1-anir-timer = 200
>r1-modified = no
>
>
>Rafael Espinosa
>Network Engineer
>respinos@latino.net.co
>http://www.latino.net.co
>LAtinonet 
>
>thanks
>
>++ Ascend Users Mailing List ++
>To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
>To get FAQ'd:	<http://www.nealis.net/ascend/faq>
>

=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
 KY Lee                                                  
 Network Development Engineer,  !networX                    
 !nternet Services,  COINS               
 TELEKOM MALAYSIA  BERHAD [128740-P]
 Fax : +60 -(0)3 - 7042204   
 http://www.tm.net.my

 Time Zone : GMT+ 8 
 =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>