(ASCEND) 7.0.26 for TNT

[Matt Holdrege <matt@ascend.com>]

MAX TNT TAOS 7.0.26 software has been given to Customer Support. This 
release contains the following:

Corrections:
*TR 4896 PPP calls no longer fail when setting Auth-Frm-Addr-Start is set to
yes
*TR 4966 NAS-Port attribute in RADIUS accounting now reported as documented.
*TR 5115 Repeated reset with FE-29.
*TR 5539, 1000033 Auth and Accounting packets are no longer sent to 
destination port 0.
*TR 5482 Synch users no longer fail to connect with "Cant Open 1 HDLC 
Channel."
*TR 258937 Ping and traceroute now work properly when set to no for terminal
servers.
*TR 1000235 E1 R2 no longer blocking calls from the switch when call rates 
are high
*AppleTalk node now released if ATCP is not negotiated.
*CSM3V cards no longer fail SAR external loopback test.
*Calls no longer fail to come up when IP pools are changed.
*Hardware revision number can be number as well as alphabetical.
*MAX TNT no longer resets with no fatal log on a jump to 0
*Insertion of a power supply cord now causes the NAS to generate a power 
supply state change trap.
*L2TP now parses vendor specific Attribute Value Pairs (AVPs)
*RADIUS accounting now works properly when auth-type is set to RADIUS/LOGOUT
*Ethernet1: Numerous MMU resets no longer occurring.
Conexant firmware versions:
The Conexant firmware versions for Series56, Series56 II, and Series56 III
modules include support for V.90, K56flex, K56plus, and all slower, standard
modem speeds. This release includes the following Conexant firmware:
*V.34 Digital Modem modules support V1.610G24-V34_DP firmware.
*Series56 Digital Modem modules (also called CSM/1, Model Number
TNT-SL-48MOD-S56) support V2.098-K56_2M_DLP_CSM firmware.
*Series56 II Digital Modem modules (also called CSM/3, Model Numbers
TNT-SL-48MOD-SGL and TNT-SL-48MOD-S-C) support V5.814 firmware.
*Series56 III Digital Modem modules (also called CSM/3V, Model Number
TNT-SL-48MODV3-S-C) support V5.814 firmware.
Known Issues:
*Use of this release is not recommended with Rev. B or lower of the 
Ethernet-2 card (TNT-SL-E10-100, part number 0800-0433-001).
*If you have a Rev. B or lower Ethernet-2 card, contact your Ascend
representative to obtain an upgrade to Rev. C or higher. The Rev. B or lower
cards continue to work with releases earlier than 7.0.0.
*MP bonding of analog calls is supported, but some client modems and 
software may have compatibility problems.
*Configurable receive and transmit data rate limits are not supported on 
the DS3 ATM card. They are supported on the CAP-RADSL, SDSL, and 
unchannelized DS3 cards.
*If you replace an older Ethernet card with the new Ethernet-2 card, you 
must write new Ethernet profiles for the new card. The old Ethernet 
profiles do not carry forward.
*Connection profiles for ATMP mobile clients ignore the Shared-Profile 
setting. Shared-Profile is implicitly set to Yes for all ATMP mobile client 
Connection profiles.
*LAN-Modem profiles contain entries for 96 devices. For 48-port modem cards,
only the first 48 entries are used.
*This release is not recommended for use with DM48-v.34 cards under heavy 
load.
*In this release, if a Debug profile exists for the Series56-II card, the 
card may generate messages such as the following during normal operation:

WARNING: Index: 4005 Revision: 7.0.6 Slot 1/7 (tntcsmx)
Date: 02/25/1999. Time: 20:08:02
Location: e00772bc e0149cac e0142868 e00dc340 e00dc078 e0025ec8
WARNING: Index: 4105 Revision: 7.0.6 Slot 1/7 (tntcsmx)
Date: 02/25/1999. Time: 20:08:09
Location: e0077804 e0149c58 e0140cac e0149a84 e007b098 e0085144
These messages can and should be suppressed, to avoid distracting attention 
from actual alerts. The procedure for disabling the warnings is described 
in "TR4582" on page 37

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>