Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
(ASCEND) Problem with a P75 not dialing out.
I've had a problem with my P75 not dialing out.
It dials to three locations, each part of a class C address, with variable
subnetting.
P75 xxx.xx.xxx.129/27 +5.0Ap7+ (this is me)
P400 xxx.xx.xxx.1/27 +4.6C+ (this is my connection to the
outside world)
P75 xxx.xx.xxx.233/29 +5.0Ap7+
P25 xxx.xx.xxx.225/29 +5.0Ap5+ (P25 Classic w/ IP routing)
This is the route table in the P75.
Destination Gateway IF Flg Pref Met Use Age
0.0.0.0/0 xxx.xx.xxx.1 wanidle0 SGP 100 7 26588 259614
127.0.0.1/32 - lo0 CP 0 0 0 259614
127.0.0.2/32 - rj0 CP 0 0 0 259614
127.0.0.3/32 - bh0 CP 0 0 0 259614
xxx.xx.xxx.0/27 xxx.xx.xxx.1 wanidle0 SG 120 7 3405 259614
xxx.xx.xxx.1/32 xxx.xx.xxx.1 wanidle0 S 120 7 57 259614
xxx.xx.xxx.128/27 - ie0 C 0 0 6542 259614
xxx.xx.xxx.129/32 - lo0 CP 0 0 0 259614
xxx.xx.xxx.224/29 xxx.xx.xxx.225 wanidle0 SG 120 7 1724 259614
xxx.xx.xxx.225/32 xxx.xx.xxx.225 wanidle0 S 120 7 1 259614
xxx.xx.xxx.232/29 xxx.xx.xxx.233 wanidle0 SG 120 7 154 259614
xxx.xx.xxx.233/32 xxx.xx.xxx.233 wanidle0 S 120 7 1 259614
255.255.255.255/32 - ie0 CP 0 0 0 259614
Neither of my BRI channels were in
use. My machine is 130. On my machine, I attempted to ping 1. I also had
a telnet window running to my P75. When I started the ping loop, the
telnet window did not show any activity attempting to call the P400.
After about 20 seconds the p75 showed itself as calling, then connected,
and then ping packets started to transfer.
The above route listing was taken after I had started the ping loop, but
it hadn't attempted to connect yet.
I have the line "Call Filter=1" in the session options to the P400. I have
not set up filters differently from the default factory filters. I have
the same line in each connection profile.
Is there something I'm doing stupid here?
Have the default call filters changed since version 4?
Why are features being added in the patch tree? (50Ap7 added up and down
metrics, and up and down preferences)
If I do a RIP=Both-v2 in my profile to the P400 will the P400 properly
expire the route metrics when the connection drops? (remembering that the
P400 is running old software)
Is there any way of controlling the RIP in the P25, or does it do RIP at
all? (the P25 calls me and the P400 for work and internet connectivity)
Thanks.
---
William C Bonner <wbonner@lgx.com> 6110 E Mockingbird Ln
Home Fax: +1-214-692-9277 Voice: +1-214-692-9278 Suite 102-762
Work Fax: +1-214-989-9782 Voice: +1-214-989-9781 Dallas, TX 75214-2600
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.shore.net/~dreaming/ascend-faq>
or <ftp://ftp.shore.net/members/dreaming/ascend-faq.txt>