Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

(ASCEND) Re: SNMP and OS = BUG?



I kind of ran into the same problem but after I telnetted to the box
to see it was actually upgrading (you can go into debug mode
and watch the little .......... thingies go by) I just let the box sit
a few minutes and eventually SNMP services returned and that's when
I knew it was ready.  

You're right though, the box doesn't respond to any SNMP commands
while it's upgrading.  I'm certain that's for a reason though.

Just wait for the box for about 5-6 minutes as it downloads firmware.
Also ensure your TFTP path is an absolute pathname. 


At 03:36 AM 9/19/97 -0400, Jason Nealis wrote:
>
>Ok, Something is strange here, I set everything according to your
>descriptions below. 
>
>ascend.systemStatusGroup.sysConfigTftp.sysConfigTftpHostAddr.0 a x.x.x.x
>ascend.systemStatusGroup.sysConfigTftp.sysConfigTftpFilename.0 s tim.m40
>ascend.systemStatusGroup.sysConfigTftp.sysConfigTftpCmd.0 i 6  
>
>Then the box goes into a continual upgrade, It upgraded approx 3-4 times
>before it will get to the command prompt.
>
>It looks as if the MAX is not returning the box back what I would guess
>would be a integer of 0. Or what ever regular run time would be. 
>
>Also durring the upgrade it doesn't respond to any snmpsets, So I can't 
>log a reset in there.
>
>BUG? Or am I do this wrong?
>
>Jason Nealis
>Director Internet Operations
>Network Access 
>Erols Internet
>
>
>
>On Thu, 18 Sep 1997, Kenneth Packert wrote:
>
>> This TFTP command has six options as shown. 
>> 
>> sysConfigTftpCmd OBJECT-TYPE
>> 	SYNTAX	INTEGER {
>> 		    save( 1 ),		-- save configuration
>> 		    restore( 2 ),	-- restore configuration
>> 		    saveAll( 3 ),	-- save ALL config options
>> 		    saveMib( 4 ),	-- save config w/MIB numbers
>> 		    saveAllMib( 5 ),	-- save ALL config w/MIB numbers
>> 		    loadCode( 6 )	-- load a code image
>> 		}
>> 	ACCESS	read-write
>> 	STATUS	mandatory
>> 	DESCRIPTION
>> 	   "This variable instructs the system to perform the specified
>> 	    tftp operation."
>> 	::= { sysConfigTftp 1 }
>> 
>> The reboot is:
>>  sysReset            OBJECT-TYPE
>> 	SYNTAX		INTEGER {
>>                         no-op( 1 ),
>>                         reset( 2 ) 
>>                         }
>> 	ACCESS		read-write
>> 	STATUS		mandatory
>> 	DESCRIPTION	"The reset takes effect after 1 minute."
>> 	::= { systemStatusGroup 8 }
>>  
>> ken
>> -----Original Message-----
>> From:	Jason Nealis [SMTP:nealis@babylon.erols.com]
>> Sent:	Thursday, September 18, 1997 8:43 AM
>> To:	John Coy
>> Cc:	ascend-users@max.bungi.com
>> Subject:	Re: (ASCEND) SNMP and OS?
>> 
>> 
>>  
>> 
>> On Wed, 17 Sep 1997, John Coy wrote:
>> 
>> > JASON!!! From your FAQ man!
>> >
>> :)
>> 
>>  
>> > Actually, the MIB variables do exist.  They are as follows:
>> > 
>> > iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).
>> >     ascend(529).systemStatusGroup(9).sysConfigTftp(5).
>> >     sysConfigTftpCmd(1)
>> > 
>> > Where it's set value determines behavior:
>> > 
>> > loadCode	load firmware code 
>> > restore	restore config via TFTP
>> > save		save config via TFTP
>> 
>> That's my fault, I got all confused and thought the sysConfigTftpCmd was
>> only for saving configurations, I was not aware of the seperate status 
>> codes. 
>> 
>> 
>> 
>> > 
>> > You set file locations and SNMP server locations using the:
>> > 
>> > sysConfigTftpHostAddr(3)
>> > sysConfigTftpFilename(4)
>> > 
>> > I got all this worked out too but I couldn't get the damned
>> > MAX boxes to reboot using SNMP.  Go figure huh?  Let me know if
>> > you can figure out how to get them to reboot (I know the variable
>> > it just doesn't do anything when I set it).
>> > 
>> > At 05:04 PM 9/17/97 -0400, you wrote:
>> > >
>> > >
>> > > OK, I'm was able to bang a script together that would go out and save
>> > >all my configurations via tftp to my tftp server, Next challenge is 
>> > >to do OS upgrades via tftp. I search through the Ascend Mib and I didn't
>> > >see anything in regards to OS upgrades and SNMP, BUT I know Ascend's 
>> > >new Navis Acess thingie will also do this, And I'm guess that it's
>> > >done via SNMP, Or does it actually do some sort of expect script 
>> > >and step through the menu system?
>> > >
>> > >Summary: Do mib variables exist for me to upgrade OS's via SNMP?
>> > >
>> > >         If so what are they?
>> > >
>> > >Jason Nealis
>> > >Erols Internet
>> > >
>> > >
>> > >++ Ascend Users Mailing List ++
>> > >To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
>> > >To get FAQ'd:	<http://www.nealis.net/ascend/faq>
>> > >
>> > >
>> > 
>> 
>> ++ Ascend Users Mailing List ++
>> To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
>> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
>> 
>
>
++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>


References: