Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: (ASCEND) P50

Routing table shows 207.xxx.3.32/29 for the net and 207.xxx.3.33/32 for
the p50 wan session. On the other max it shows the same with ether info
coming from the max dialed into. 


East County Internet Services, Inc
-Jess-
CFO
System Admin

On Tue, 7 Oct 1997, Kevin Smith wrote:

> Now we have at least 2 threads on this subject.....did we get routing table
> info from the MAXen when this "failure" occurs ?
> 
> At 07:34 AM 10/7/97 -0700, Jesse Martinez wrote:
> >I'm runing OSPF with rip turned off.
> >
> >
> >East County Internet Services, Inc
> >-Jess-
> >CFO
> >System Admin
> >
> >On Mon, 6 Oct 1997, Kevin Smith wrote:
> >
> >> You didn't mention if you are using a routing protocol here to handle the
> >> dynamic updates that would be required to do this ?
> >> 
> >> At 07:51 PM 10/6/97 -0700, Jesse Martinez wrote:
> >> >I have only one static route. The default route that points to my router.
> >> >Both maxes point to the same router. I heard something about an attribute
> >> >called ascend-if-address but when I tried that the p50 wouldn't route at
> >> >all. Any other suggestions.
> >> >
> >> >
> >> >East County Internet Services, Inc
> >> >-Jess-
> >> >CFO
> >> >System Admin
> >> >
> >> >On Mon, 6 Oct 1997, Kevin Smith wrote:
> >> >
> >> >> At 12:00 PM 10/4/97 -0700, Jesse Martinez wrote:
> >> >> >I have a user with a Pipeline 50. Not sure the rev of software he
> has. My
> >> >> >question is how do I set up radius to allow him to connect to either of
> >> >> >two maxes and route without problems. I gave him a subnet of 248 to use
> >> >> >and when he connect to the first max in a hunt group he's ok. If the
> call
> >> >> >hits the second max then he can't route. I've never configured a p50 so
> >> >> >I'm not sure of the settings on his side. Both maxes are in the same
> hunt
> >> >> >group.
> >> >> 
> >> >> Whichever MAX picks up the RADIUS entry should start advertising the
> >> route to
> >> >> the P50 via a routing protocol (RIPv2 or OSPF). Do you have static
> routes
> >> >> setup that could be over-riding this ?
> >> >> 
> >> >> 
> >> >> Kevin
> >> >> 
> >> >> 
> >> >> ++ Ascend Users Mailing List ++
> >> >> To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> >> >> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >> >> 
> >> >
> >> >++ Ascend Users Mailing List ++
> >> >To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> >> >To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >> >
> >> 
> >> Kevin
> >> 
> >> 
> >> ++ Ascend Users Mailing List ++
> >> To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> >> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >> 
> >
> >++ Ascend Users Mailing List ++
> >To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
> >To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >
> 
> Kevin
> 
> 
> 

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>
References: