Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ASCEND) P75 -> Max : CL OK c=47?
At 02:11 PM 10/9/97 -0000, Peter Leigh wrote:
>
>connection nwnet:
> Active=Yes
> Encaps=PPP
> Dial #= (our ISDN number)
> Calling #=
> Called #=
> Route IP=Yes
> Route IPX=N/A
> Bridge=N/A
> Dial Brdcast=N/A
>
>(nwnet) Encaps Options:
> Send Auth=PAP <-- this is correct
> Send PW=*******
> Recv PW=N/A
> MRU=1524
> LQM=No
> LQM Min=600
> LQM Max=600
> Link Comp=None
> VJ Com=No
>
>Ip Options:
> LAN Adrs=0.0.0.0/0
This is not consistent with the "configure" entries you detail below...
> WAN Alias=0.0.0.0
> IF Adrs=0.0.0.0/0
> Preference=100
> Metric=7
> Private=No
> RIP=Off
> [...]
>
>IPX Options all = N/A
>
>Session Options
> Data Filter=0
> Call Filter=0
> Filter Persistence=No
> Idle=15
> Preempt=60
> IPX SAP Filter=0
> Backup=
> Secondary=
>
> Telco options...
> AnsOrig=Ans Only
Answer only, means the P75 should not be calling out with this profile...
there must be another profile he's using to get to your max...
> Callback=No
> Exp Callback=No
> Call Type=Switched
> Group=N/A
> FT1 Caller=N/A
> Data Svc=64K
> Force 56=No
> Bill #=
> Transit #=
>
>Answer -> PPP Options
>
> Route IP=Yes
> Route IPX=N/A
> Bridge=N/A
> Recv Auth=NONE
> MRU=1524
> LQM=No
> LQM Min=600
> LQM Max=600
> Link Comp=None
> VJ Comp=No
> BACP=No
> Dyn Alg=Quadratic <<-- seems to indicate mpp is turned on somewhere ..?
No. It just means the P75 is *allowing* incoming calls to connect with MP+ -
since this is in the "answer" configuration.
>
>Configure ...
>
> Switch Type=UK
> Chan Usage=Switch/Switch
> My Num A=
> My Num B=
> SPID 1=N/A
> SPID 2=N/A
> Data Usage=A
> Phone 1 Usage=None
> Phone 2 Usage=None
> Phone Num Binding=N/A
> My Name=<login name>
> My Addr=(his local IP address - I've suggested he make it 192.168. ...)
Does this show up in the ethernet/mod config/ether options ??
> Rem Name=nwnet
> Rem Addr=(address/subnet of our MAX)
This is what should appear in the configuration above if its set here and
*saved*....
> Dial #=(our ISDN number)
> Route=IP
> NAT Routing=NO
> NAT Profile=N/A
>
>Thanks!!
...sent to you from an NT4.0 workstation connected to a P75 (via a mini-hub),
dialed into a MAX4000 (using NAT).... ;)
Kevin
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>
Follow-Ups:
References: