[snip] > Sure enough the 1.3A release notes suggest there's something wrong and you > should retry (maybe re-download the tar file as you did)...but in the 1.3Ap6 > release notes there is another warning (see step 4): That's always my first thought, check the file integrity before blaming the procedure. I can remember when I used to forget to type "bi" at the FTP prompt to switch from Ascii to Binary. So, I check it blaming it on human error first (mine). [snip] > 1 Download the binaries from Ascend's FTP server to a local host. > 2 Log into the MAX TNT. > 3 Load the upgrade shelf-controller software. For example, to load via TFTP > from host1: > admin> load boot-sr network host1 tntsr.bin > 4 Load the upgrade tar file. For example: > admin> load tar network host1 tntrel.tar > Note: This load might not be successful. It might stop with the error > message "load > aborted: invalid image ..." This is okay. Well, this is as far as I got. Would you believe it if I told you that I had this very same error almost a month ago? We called tech support then too and they didn't even know why it had happened. We actually had to revert back to 1.2 (at the time, it was 1.2Ap10, and we wanted to go to 1.3Ap2). So, we installed 1.2Ap12. Long story short, this wasn't the first time we asked about it. And both times the techs that we spoke to still didn't know. I can understand the first time saying he didn't know as the code was still new. But a month later, that's inexcusable. > 5 Use the Dircode and Fsck 1 commands to verify that the images are good. > If for any > reason the verification shows the files are not all okay or are of the > wrong release, format > the flash card with the Format 1 command and repeat from Step 4. I did this as the tech's suggestion. > 6 Use the Reset command to execute the new shelf-controller software. > admin> reset > 7 Log into the MAX TNT again and load the upgrade tar file a second time. > It should I did this as my own suggestion. (Good thing I listen when I'm talking to myself) > complete properly this time. For example: > admin> load tar network host1 tntrel.tar > <<<< Yep. I did that while waiting on hold for the ascend drone to find out from the Collective what he should do. Was Atif not linked to the Collective that day? ;) > Is this effectively the steps that you did take to get the code to load? Yes, it was, but via trial and error and waiting on hold for the drone to find out what we should do. -- Joseph Hickman Director of Network Operations josephh@psn.net / iconia@psn.net ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>> </PRE> <!--X-MsgBody-End--> <!--X-Follow-Ups--> <HR> <STRONG>Follow-Ups</STRONG>: <UL> <LI><STRONG><A HREF="msg09377.html">Re: (ASCEND) Max TNT upgrade from 1.2ap12 to 1.3Ap6</A></STRONG></LI> <UL> <LI><EM>From</EM>: Kevin Smith <kevin@ascend.com></LI> </UL> </UL> <!--X-Follow-Ups-End--> <!--X-References--> <STRONG>References</STRONG>: <UL> <LI><STRONG><A HREF="msg09337.html">Re: (ASCEND) Max TNT upgrade from 1.2ap12 to 1.3Ap6</A></STRONG></LI> <UL> <LI><EM>From</EM>: Kevin Smith <kevin@ascend.com></LI> </UL> </UL> <!--X-References-End--> <!--X-BotPNI--> <HR> <UL> <LI>Prev by Date: <STRONG><A HREF="msg09359.html">Re: (ASCEND) K56 and Chasis.</A></STRONG> </LI> <LI>Next by Date: <STRONG><A HREF="msg09356.html">Re: (ASCEND) V110 and Eriksen Not Connecting</A></STRONG> </LI> <LI>Prev by thread: <STRONG><A HREF="msg09339.html">Re: (ASCEND) Max TNT upgrade from 1.2ap12 to 1.3Ap6</A></STRONG> </LI> <LI>Next by thread: <STRONG><A HREF="msg09377.html">Re: (ASCEND) Max TNT upgrade from 1.2ap12 to 1.3Ap6</A></STRONG> </LI> <LI>Index(es): <UL> <LI><A HREF="mail27.html#09357"><STRONG>Main</STRONG></A></LI> <LI><A HREF="thrd190.html#09357"><STRONG>Thread</STRONG></A></LI> </UL> </LI> </UL> <!--X-BotPNI-End--> <!--X-User-Footer--> <!--X-User-Footer-End--> </BODY> </HTML>