This is not consistent with the "configure" entries you detail below... > WAN Alias=0.0.0.0 > IF Adrs=0.0.0.0/0 > Preference=100 > Metric=7 > Private=No > RIP=Off > [...] > >IPX Options all = N/A > >Session Options > Data Filter=0 > Call Filter=0 > Filter Persistence=No > Idle=15 > Preempt=60 > IPX SAP Filter=0 > Backup= > Secondary= > > Telco options... > AnsOrig=Ans Only Answer only, means the P75 should not be calling out with this profile... there must be another profile he's using to get to your max... > Callback=No > Exp Callback=No > Call Type=Switched > Group=N/A > FT1 Caller=N/A > Data Svc=64K > Force 56=No > Bill #= > Transit #= > >Answer -> PPP Options > > Route IP=Yes > Route IPX=N/A > Bridge=N/A > Recv Auth=NONE > MRU=1524 > LQM=No > LQM Min=600 > LQM Max=600 > Link Comp=None > VJ Comp=No > BACP=No > Dyn Alg=Quadratic <<-- seems to indicate mpp is turned on somewhere ..? No. It just means the P75 is *allowing* incoming calls to connect with MP+ - since this is in the "answer" configuration. > >Configure ... > > Switch Type=UK > Chan Usage=Switch/Switch > My Num A= > My Num B= > SPID 1=N/A > SPID 2=N/A > Data Usage=A > Phone 1 Usage=None > Phone 2 Usage=None > Phone Num Binding=N/A > My Name=<login name> > My Addr=(his local IP address - I've suggested he make it 192.168. ...) Does this show up in the ethernet/mod config/ether options ?? > Rem Name=nwnet > Rem Addr=(address/subnet of our MAX) This is what should appear in the configuration above if its set here and *saved*.... > Dial #=(our ISDN number) > Route=IP > NAT Routing=NO > NAT Profile=N/A > >Thanks!! ...sent to you from an NT4.0 workstation connected to a P75 (via a mini-hub), dialed into a MAX4000 (using NAT).... ;) Kevin ++ Ascend Users Mailing List ++ To unsubscribe: send unsubscribe to ascend-users-request@bungi.com To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>> </PRE> <!--X-MsgBody-End--> <!--X-Follow-Ups--> <HR> <STRONG>Follow-Ups</STRONG>: <UL> <LI><STRONG><A HREF="msg09727.html">Re: (ASCEND) P75 -> Max : CL OK c=47?</A></STRONG></LI> <UL> <LI><EM>From</EM>: Peter Leigh <pete@nwnet.co.uk></LI> </UL> </UL> <!--X-Follow-Ups-End--> <!--X-References--> <STRONG>References</STRONG>: <UL> <LI><STRONG><A HREF="msg09577.html">(ASCEND) P75 -> Max : CL OK c=47?</A></STRONG></LI> <UL> <LI><EM>From</EM>: Peter Leigh <pete@nwnet.co.uk></LI> </UL> </UL> <!--X-References-End--> <!--X-BotPNI--> <HR> <UL> <LI>Prev by Date: <STRONG><A HREF="msg09707.html">Re: (ASCEND) numbered interfaces</A></STRONG> </LI> <LI>Next by Date: <STRONG><A HREF="msg09708.html">Re: (ASCEND) P75 - Deleting Code</A></STRONG> </LI> <LI>Prev by thread: <STRONG><A HREF="msg09577.html">(ASCEND) P75 -> Max : CL OK c=47?</A></STRONG> </LI> <LI>Next by thread: <STRONG><A HREF="msg09727.html">Re: (ASCEND) P75 -> Max : CL OK c=47?</A></STRONG> </LI> <LI>Index(es): <UL> <LI><A HREF="mail13.html#09709"><STRONG>Main</STRONG></A></LI> <LI><A HREF="thrd199.html#09709"><STRONG>Thread</STRONG></A></LI> </UL> </LI> </UL> <!--X-BotPNI-End--> <!--X-User-Footer--> <!--X-User-Footer-End--> </BODY> </HTML>